log splitter valve sticking

Rated for high pressure our hydraulic valves will have your wood splitter working like new again. Spray the top of the cylinders with a good penetrating oil and let it soak a few hours.

How To Fix The Automatic Return On A Log Splitter Offgridmaker Com

Do not use this device if the valve spool does not center or appears to stick.

. 9-6587-PB Out of Stock - More on Order. If I pull it back to retract the ram it used to go into a detent position and stay there until the ram was fully retracted and then the handle and valve would return to the neutral position. And now it started to stick going out and it will go out to the end and stall the engine.

Remove the high pressure hydraulic hose from the inlet port of the control valve using channel locks and a 1 and 18 wrench_____. Joined May 14 2017. This valve is the most prevalent valve used in the residential log splitter industry.

This tutorial apply to the Energy control valve. Prince Auto Cycle Log Splitter Valve wPower Beyond RD523MMEE5A4C1 Item Number. USE AND CARE OF KICK OFF VALVE 1.

If the oil is found to be enough then the problem is due to the air mixed with liquid when opening the bleed valve and cycling pressure plate. Work the cylinder up and down. Slide the 2 valve spool into the detent end of the valve body until the end of the spool is flush with the detent end of the valve body.

You need to check the amount of oil first. In case a log splitter stalls under load check for the model of log splitter that way it is easier to reach out to the root cause. If your log-splitter is moving slow but still capable of splitting the wood it always has it is most likely stuck in its second stage.

In the second stage or low flowhigh-pressure stage the pump produces 25 or less of its rated GPM but it does it at a higher pressure. It is preset at the factory. Remove the air from the system to solve this problem and keep the bleed valve tightened enough.

Use the correct device for the job. Operating valve sticking or obstructed November 26. Protect the valve spool from paint overspray.

Its a Huskee 22 ton and the valve is sticking both ways. SpeeCo would be willing to replace the defective valve under warranty if you would like to bring the splitter and your receipt to the dealer where you purchased it. Anyone ever rebuild a log splitter hydaulic valve.

As soon as the motor starts the carriage begins to move without pressing the lever. The penetrating oil will usually do the trick. 1 Spool Prince LS-3000-1 Log Splitter Valve Item Number.

My new to me Countyline Speeco 25 ton splitter control valve detent mechanism was sticking operating erratically and adjusting didnt solve the problem. More than enough to split just about everything but the nastiest of knarly logs. Log Splitter Hydraulic Troubleshooting 9 - 17 2.

It fixed my log splitter if you like the video please like share and subscribe. A detent valve lever can be pushed up or down to put the valve into operation. If the djusting of the detent relief stops the sticking control valve check the system pressure to see what it is actually set at and then decide if you really need to fix the problem or if its something you can live with.

Check all quick disconnects periodically to ensure proper function. Check the position of the lever. This easy-to-follow DIY repair guide shows how to replace the flexible log splitter hydraulic pump coupling in just 6 steps.

Fixing the auto-return on a hydraulic control valve usually is just a matter of tightening The bolt inside the detent cover assembly. Discussion Starter 1 4 mo ago. Therefore they wont fly down like they fly up without a load and can even get stuck so they wont move down at all.

Rated 5 out of 5. 9-1262 Out of Stock - More on Order. Also it is hard to trip the lever to get it to stop retracting.

Many of our log splitter control valve features include auto-return detent with 12-inch and 34-inch work ports. Read about gas log splitter. If youre used to the lever going one way on one log splitter you might have overlooked the valve position on a different log splitter that works differently.

Reconnect the 3 control lever to the 2 valve spool using the 4 clevis pin and 5 cotter pin. 7 Ton Electric Log Splitter Heavy Duty with Work Bench Guard Stand FM10T-7. Check the manual to be sure you have proper lever position.

On one side of the valve there is a inch long bolt only way I know how to describe it with a ball in the end. I pulled the cap and found it contaminated with moisture and it was lubricated with a silver pastegrease. If your log splitter vibrates a lot or the hydraulic cylinder wont move the flexible pump coupler could be broken or worn.

By and large log splitters are simple machines used to slice the wood into smaller pieces not often does a log splitter face any problem in functioning. While there is an adjustment screw in the valve it is for the setting the pressure relief in the control valve and will not adjust the detent assembly. By Matthieu Compact Petrol 6HP Wood Chipper Direct Drive FM6DD.

1 Spool Rapid Extend Log Splitter Valve Prince Mfg LSR-3060-3. I have a Brave Log splitter and the last few weeks the detentspoil valve has become sticky after the I split a couple of hours. With the log splitter off cycle the control valve forward and rearward several times to relieve any pressure in the hydraulic system_____ See Figure 2.

Other than that it works fine. Operating valve sticking or obstructed. How do you fix a stuck hydraulic cylinder.

The ball like a ball bearing moves in and out if you push on it and the. Shift the control lever away from the valve body and insert the new 1316 x 1-116 O-ring and 17 seal retainer. 30 GPM 12 Work Ports Power Beyond Port.

I have an old home made log splitter30 years never a lick of problemsIt has been sitting a couple of years it started like usualI worked it about 12 hour added about 1-12 quart of hydraulic fluid Sams Club AW 46 RO Hydraulic Oil finished my workThe next day I discovered the control flow valve was stuck and cannot move it also the pump is seized. When it retracts it pulls in tight and stalls the engine. It now sticks if you put it into the detnet position and you must pull it forward into the neutral position.

Faulty quick disconnects can result in high back pressure and sticking spools.

Hydraulic Valve Detent Removal Youtube

Predator 61594 20 Ton 212cc Log Splitter Owner S Manual Manualzz